Outlet Connection Thread Type

Orifice Type

Connector Type

DSE Minimum Liquid Flow Rate

Operating Principle

Maximum Operating Speed

Nozzle Hub Drive

Clean In Place (CIP) tank cleaning nozzles do not have to be removed from the vessel or disassembled after cleaning operations

Is Clean In Place (CIP)

Overall length of the part (typically measured in inches or millimeters).

Length

Socket Hex Size

Liquid Discharge Flow Rate Range

Core Number

Ball Material

Amplification Ratio

DSE Default Spray Angle

Herbicide Contact

Body Sales Part Number

Detergent Inlet Connection Size

Is Tip Alignment

Maximum Pump Head

Different nozzle types are _**“rated”**_ at various pressures, depending on the function of the nozzle and the pressure at which a spray pattern is fully formed. The flow rate (typically measured in gallons per minute or liters per minute) at the rated pressure (measured in pounds per square inch or bar) is highlighted in catalog performance tables and can serve as a reference point for comparing different nozzles.
> _Keep in mind when comparing nozzles of different types that the rated pressures may vary and will affect flow rate._

Liquid Flow Rate at Rated Pressure

Descriptive Product Type

Finish Coating

Number Of Spray Tips (Legs)

Mounting flanges for TankJet nozzles are available in various sizes and types. Common flange types include ASME® Raised Face, Three-Prong, Sanitary Tri-Clamp and JIS.

Flange Options

The range of flow (typically measured in gallons per minute or liters per minute) published in our catalog for a given nozzle. 
> _The catalog offers flow rates only for selected operating pressures so greater flow may be possible at pressures not shown in the catalog._

Liquid Flow Rate Range

Fungicide Systemic

The spray angles produced by nozzles vary from 0° for solid stream nozzles up to 180° for select hollow cone nozzles. For ease of product searching, our catalog groups spray angles into “narrow” (typically < 50°), “standard” (50°-100°) and “wide” (> 100°).
> _**Important Note:** Spray angle range for each of the basic spray patterns (flat spray, full cone, hollow cone) varies, so Spray Angle Catalog Group is most useful when searching for nozzles within a single spray pattern._

Spray Angle Catalog Code

Model

Drift Control

Gear Ratio

Outlet Connection Size

Liquid Flow Rate For Straight Stream Spray Pattern

Inlet To Spray Orifice Length

Price Type

Maximum Free Passage

Clamp Design

Trigger Position

Required Drillhole Diameter

Number Of Spray Outlets

Connection Orientation

DSE Spread Parameter

Siphon Inlet Connection Type

Spray Coverage refers to the portion of the vessel to be cleaned. TankJet nozzles offering full 360° coverage clean all interior tank surfaces. For vessels with an open top, TankJet nozzles with 180° downward coverage are available. Other coverage patterns are also available.

Spray Coverage

Square Tubing

Clamp Sales Part Number

Drop Size

GunJet spray guns are available for a wide range of operating pressures. The maximum operating pressure for any Low Pressure GunJet spray gun is 250 psi (17 bar). The maximum operating pressure for any Medium Pressure GunJet spray gun is 1000 psi (69 bar). The maximum operating pressure for any High Pressure GunJet spray gun is 4000 psi (275 bar). Be sure to check the specifications for each GunJet spray gun carefully and follow all safety guidelines.

Pressure Group

DSE Default Liquid Pressure

Fluid Nozzle Size

Products that are designated as "Food Contact" are constructed from materials that are compliant for food contact

Is Food Contact

Locating Flats

Maximum Spray Distance Horizontal Spray

C Dimension

Internal Hose Diameter

Minimum Tank Opening

Number of PWM Cycles

Flow Diagram Caption Title

PWM Voltage

Antenna Type

Navigation Configuration

Capacity At Maximum Pressure

Cylinder Behavior

Orifice Size

Maximum Liquid Discharge Temperature

Set-up Sales Part Number

Bushing and O-Ring Material

The volume of liquid passing through a nozzle (also called the nozzle’s capacity) is typically measured in gallons per minute or liters per minute. Flow rate is affected by liquid pressure and other factors, including the specific gravity and viscosity of the liquid being sprayed.
> _For more information on liquid flow rate or nozzle capacity, download our [technical reference document](https://spray.widen.net/download/spray/oeafrrites/cat75HYD_us_Tech-Reference_A.pdf) or contact your [local Spraying Systems Co. sales rep](https://www.spray.com/contact/find-a-representative)._

Liquid Flow Rate

Dry Boom Orientation

Maximum Temperature

Many hydraulic spray nozzles include a numeric capacity size in the part number. Capacity size is often related to the flow rate of the nozzle at the rated spray pressure for that nozzle. For example, the capacity size for a 1/4HH10 FullJet® nozzle is “10”, which reflects a 1.0 gpm flow rate at 10 psi.

Capacity Size

Spray products that are recirculating allow the sprayed liquid to flow back to the liquid source

Is Recirculating

Maximum Pressure With Advanced AutoJet Controllers

Check Valve Mount Side

Bar Size

Herbicide Soil Applied

Mounting Type

Maximum Transverse Spray Coverage Width Horizontal Spray

Maximum Liquid Discharge Pressure Range

Steam Inlet Connection Gender

Overflow Outlet Connection Thread Type

Slot Size

Material Code

Herbicide Systemic

Screen Material

Amperage

Liquid Flow Rate For Three Tips

DRD/TCT Drift Reduction Rating

Discharge Outlet Connection Gender

Split Eyelet Style

INRAE Drift Reduction Rating

B Dimension

Gearbox Bearings

Actual drop size (measured in microns) will vary based on flow rate and pressure. The _**“relative”**_ drop size range represents the variation in drop size across typical operating pressures for a particular nozzle.
> _If drop size is critical to your application, contact us for specific information. For basic information on drop size terminology, download our [technical reference document](https://spray.widen.net/download/spray/oeafrrites/cat75HYD_us_Tech-Reference_A.pdf) or contact your [local Spraying Systems Co. sales rep](https://www.spray.com/contact/find-a-representative)._

Relative Drop Size Range

Fertilizer Directed

Threaded nozzles are typically offered with tapered pipe threads. NPT and BSPT threads are the most common. Other thread types are available for selected nozzles.

Inlet Connection Thread Type

Overflow Outlet Connection Gender

Orientation

Application Rate For Two Tips

Fertilizer Banding

TeeJet® GPS Guidance Matrix® 430 Guidance

TeeJet® GPS Guidance Matrix® 430VF Guidance

TeeJet® Sensors and Flow Meters

Our products are grouped into these primary product types:
- Nozzle - Body _(a nozzle body without a spray tip)_
- Tip _(a spray tip without a nozzle body)_
- Assembly _(a complete nozzle assembly including both a nozzle body and a spray tip)_

Product Type

QuickMist® Quick Connect Air Atomizing Nozzles

Electrically-Actuated / Hydraulic Atomizing

Throttling and Pressure Relief/Regulating Valves

TeeJet® Matrix® 908 Field Computer

TeeJet® Matrix® 908 Field Computer, TeeJet Matrix 908 Field Computer

Model Specifications

General Information

Specification Summary

Alternative Models