JKI Drift Reduction Rating

Fertilizer Banding

Steam Inlet Connection Thread Type

The largest interior tank diameter (measured in feet or meters) for which a specific TankJet nozzle should be used.

Maximum Recommended Tank Diameter

Actual drop size (measured in microns) will vary based on flow rate and pressure. The _**“relative”**_ drop size range represents the variation in drop size across typical operating pressures for a particular nozzle.
> _If drop size is critical to your application, contact us for specific information. For basic information on drop size terminology, download our [technical reference document](https://spray.widen.net/download/spray/oeafrrites/cat75HYD_us_Tech-Reference_A.pdf) or contact your [local Spraying Systems Co. sales rep](https://www.spray.com/contact/find-a-representative)._

Relative Drop Size Range

Maximum Transverse Spray Coverage Width Horizontal Spray

Motor Cables

Nozzle Hub Drive

Actual drop size (measured in microns) will vary based on flow rate and pressure. The _**“relative”**_ drop size range represents the variation in drop size across typical operating pressures for a particular nozzle.

The drop size ranges provided can be characterized as follows:
- 10 to 500 microns: very small drops
(comparable to fog)
- 100 to 500 microns: small drops
(comparable to light rain)
- 500 to 1000 microns: medium drops
(comparable to moderate rain)
- 1000 to 5000 microns: large drops
(comparable to heavy rain)

> _If drop size is critical to your application, contact your [local Spraying Systems Co. sales rep](https://www.spray.com/contact/find-a-representative)._

> _For basic information on drop size terminology, download our [technical reference document](https://spray.widen.net/download/spray/oeafrrites/cat75HYD_us_Tech-Reference_A.pdf) or contact your [local Spraying Systems Co. sales rep](https://www.spray.com/contact/find-a-representative)._

Relative Drop Size Group

Formula

Maximum Pressure With Advanced AutoJet Controllers

Provided for flat spray nozzles with elliptical orifices. It is the diameter of a circular orifice that would pass the same flow.

Equivalent Orifice Diameter

Minimum Pressure

Overflow Outlet Connection Size

Mounting Points

Answercode to a specific question

Air Knife Length

Overflow Outlet Connection Thread Type

DSE Volume Median Diameter (Dv 0.5)

Flats

Has Guide Vane

Set-up Sales Part Number

Fluid Cap Part Number

Cap Hex Size

Number Of Trigger Signals

Minimum Cylinder Air Pressure

Steam Capacity Range

The volume of liquid passing through a nozzle (also called the nozzle’s capacity) is typically measured in gallons per minute or liters per minute. Flow rate is affected by liquid pressure and other factors, including the specific gravity and viscosity of the liquid being sprayed.
> _For more information on liquid flow rate or nozzle capacity, download our [technical reference document](https://spray.widen.net/download/spray/oeafrrites/cat75HYD_us_Tech-Reference_A.pdf) or contact your [local Spraying Systems Co. sales rep](https://www.spray.com/contact/find-a-representative)._

Liquid Flow Rate

Mounting Type

Length At Maximum Opening Height

Sanitary Standard

Descriptive Product Type

Siphon Inlet Connection Size

Maximum Liquid Discharge Pressure Range

Number Of Spray Outlets

Electrical Side Spare Part Kit

Motor Version

A Dimension

Finish Coating

Anti-Bearding Set-Up

Maximum Temperature

Spray products that are recirculating allow the sprayed liquid to flow back to the liquid source

Is Recirculating

Front Spray Angle at Rated Pressure

Products that are designated as "Food Contact" are constructed from materials that are compliant for food contact

Is Food Contact

Clamp Sales Part Number

Check Valve Mount Side

GunJet spray guns and accessories are available with various outlets, including NPT or BSPT threaded outlets, UniJet threaded outlets (11/16-16) and quick-connect outlets.

Outlet Connection Type

Cylinder Behavior

Orifice discs and cores are used in some UniJet® full cone and hollow cone nozzles to control spray characteristics. Each disc and core pairing provides an unique and different combination of flow rate, spray angle and spray pattern.

Orifice Disc Number And Core Number

Is Temperature Controlled

Mesh size relates to the particle size that will be filtered by a strainer. Because the purpose of a liquid strainer is to prevent nozzle plugging, it’s important to choose a mesh size that will screen out particulates larger than the nozzle’s orifice will allow to pass. > _For help selecting the right strainer mesh size for your application, contact your [local Spraying Systems Co. sales rep](https://www.spray.com/contact/find-a-representative)._

Mesh Size

Maximum Pump Head

Operating Pressure Range

PWM Voltage

Number Of Speed Control Channels

Outlet Connection Thread Type

Orifice Number

Orifice Type

Amperage

The nozzle height is set to ensure the optimal spray pattern overlap, which is necessary for uniform coverage based on the spacing of the nozzles across the spray boom.

Optimum Spray Height (Height @ Spacing)

Max Horizontal Throw For Straight Stream Spray Pattern

Approximate Spray Pattern Diameter

Inner Clamp Sales Part Number

Boom Diameter

Navigation Configuration

Minimum Tank Opening

Maximum Free Passage

C Dimension

Pipe Size To Clamp On

Motor Specifications

JKI Certification Number

Inlet Type

Application Rate For Three Tips

Air Volume at Outlet

Cycle Time

Extension Length

Mesh Opening

Weight

The QuickJet® and UniJet® Nozzle Systems provide nozzle bodies with interchangeable spray tips. QuickJet bodies and tips are designated with “Q” as the first letter in the part number and offer quick-connect convenience with automatic spray pattern alignment. UniJet bodies and tips use a threaded retaining cap to complete the assembly. Both QuickJet and UniJet nozzles are available in a wide variety of spray patterns, flow rates and materials of construction.

Tip Type

Gearbox Type

Other Metallurgy

Has Cleanout Needle

Horizontal Spray Coverage Length Horizontal Spray

Antenna Type

LERAPS Drift Reduction Rating

DSE Spread Parameter

Drop Size

Application

DSE Calculation Enabled

Application Rate

Air Flow Rate

Dense Spray Coverage Diameter

Spray Coverage refers to the portion of the vessel to be cleaned. TankJet nozzles offering full 360° coverage clean all interior tank surfaces. For vessels with an open top, TankJet nozzles with 180° downward coverage are available. Other coverage patterns are also available.

Spray Coverage

Circulation Rate

Estimated Ready to Ship

Nozzle Count

Atomizing Air Flow Rate

Extension Options

Tip Style Or Setup

58456 Large Quick Connect Fittings

CP98497-PP Large Quick Connect Fittings

116240-LM Large Quick Connect Fittings

CP37166-1-30255 Large Quick Connect Fittings

Maximum Pressure

Our products are grouped into these primary product types:
- Nozzle - Body _(a nozzle body without a spray tip)_
- Tip _(a spray tip without a nozzle body)_
- Assembly _(a complete nozzle assembly including both a nozzle body and a spray tip)_

Product Type

QuickMist® Quick Connect Air Atomizing Nozzles

Electrically-Actuated / Hydraulic Atomizing

Throttling and Pressure Relief/Regulating Valves

* Used for 430 and 530 manifold inlets and select ball valves.* Rated to 215 PSI.* O-Ring (FKM)

CP7717-M40X4-VI Large Quick Connect Fittings

CP7717-M40X4-VI Large Quick Connect Fittings, CP7717-M40X4-VI

Model Specifications

General Information

Description

Specification Summary

Alternative Models